Doing so will prevent them from getting captured between the ceiling and canopy. As you can see, this operation is fairly simple, as long as you have some knowledge of this type of electrical installation. You just need to remember that an electrical box that is used for a ceiling light will not accommodate a ceiling fan. It is simply too light and flimsy to hold the fan. Any fan needs to be replaced with an electrical box that is specifically designed for fans. That is usually the normal anatomy.
Include a decorative ceiling medallion to cover the former light fixture hole, especially if you are installing the fan in an older home. When adding the ceiling medallion, apply a bead of a urethane-based glue to the back of the medallion.
Pass the wiring through the medallion and center the medallion over the pancake box before pressing it tight into place. To finish off the work, add four finishing nails 6d and drive them into the ceiling joist.
Establish the nail heads before spackling or caulking. If you need to paint the medallion, you should do so before you add the ceiling plate for the fan. After the paint dries, hold the metal ceiling plate or the fan up to the pancake box, pulling the wiring through the center.
Feed the wiring that emerges from the motor through the canopy center. Set the canopy over the motor. Remember that the threads on the pipe have a coating that has been applied in the factory. Therefore, you should never remove the coating. The finish keeps the pipe intact or keeps it from unscrewing. When you attach the blades for the fan, affix each blade to an iron, or a bracket that holds each blade on the fan.
Fasten the irons for the blades to the motor. Screws are usually provided by the manufacture. If the fan features lighting, you will next need to add the lightbulbs and shades. Screw the holder for the remote control next the wall beside the wall switch. Once you follow the above basic steps, you will find that your ceiling fan will indeed impact your overall comfort and livability. While the fan can keep you cool during the sultry days of summer, it can also pull air down into a room during the winter time.
If the fan is lighted, you can also use the fan as your major source of lighting. Replacing a current light fixture with a ceiling fan takes about one day, as the wiring and connections are already in place. When you are taking on this type of project, you need to use a volt meter to make sure the electricity is disengaged and methodically follow each of the above steps. The above information gives you an idea of what to expect.
Once you have the ceiling fan assembled and ready to mount, make sure the power is still switched off and that a family member has not reconnected the electricity. While this task is fairly easy, once you learn the steps, you still need to make sure everything is safe. Installing a ceiling fan will lead you to consider the installation for other parts of your home, once you learn how much money you can save in energy usage.
The addition of a fan circulates the air so you can optimize the use of your heating or cooling system. For this reason, the fans are currently trending among homeowners and businesses, as they make the best use of energy efficiency. If you are not sure about anything regarding the wiring, ask an electrician and make sure you are well versed in this area.
This is not one of those projects that you should consider trial by error, as the error you may make can cost you your life. When handling any type of wiring, it is imperative that you are extremely careful. Even if the task is small or light, you cannot ignore the seriousness of any electrical injury.
Before You Begin. How To Install A Ceiling Fan Without Attic Access The following instructions are basic instructions that will assist you in adding your ceiling fan with a good amount of ease. Step 1 After you have made sure that you turned off the power, you can remove the current light fixture.
Step 2 Next, you need to remove the fixture box. Step 4 Twist the bracket to expand it. Step 5 Get rid of the knockout on the mounting box and add the grommet. Step 6 Insert the wires through the grommet before adding them inside the box. Braces will mount in different ways but the easiest ones allow you to wedge the brace against the ceiling joists so that it goes in quickly and firmly.
Check out the directions for your specific brace and then get it mounted in your ceiling joists and we are ready for the next step. Push out the tabs that you find so that you can thread your existing wiring into your electric box in preparation for the new fan. Be sure that you screw it in tightly so that the electrical box is flush and secure. It should not wiggle or move at all when you apply pressure, and this is especially important with a moving fixture such as a ceiling fan, so make sure it is flush and secure before we proceed.
Depending on the make and model of your new fan, the actual mounting and installation steps may vary. Take a look at the documentation which comes with your new fan and follow the mounting instructions which the manufacturer has provided. Typically, the mounting process will be pretty basic, but your fan may have some additional steps to ensure stability to stop it from wobbling and safe operation, so be sure to check the manual so that the fan will be mounted properly and we are ready to finalize the wiring.
The fan wires are color coded in most cases, so we can attach them to the wires from your wiring box with confidence. Simply connect the white wires from your fan to the white wires in your electrical box, and do that same with the black wires from your fan as well. Again, if you are not confident working with electric, please enlist the help of a professional.
Once the wires are connected then you can push them neatly into the electrical box and we are now ready to complete the aesthetics for the newly wired fan.
This is just going to require pushing the trim ring up to tighten it in place so that it is flush against the ceiling and now your brand-new fan should look fully installed.
0コメント