GND Q3 A. Output voltage is Focusing, tracking, sled and spindle servo processing. During serial writer is connected. L : Power supply ON. After replacing the following parts, adjust as follows. You can only view or download manuals with. Sign Up and get 5 for free. If the unit still does not operate normally after a while, consult your Kenwood dealer. The unit returns to factory settings when the Reset button is pressed. Normal operation should be restored. Therefore, what appears on the display in the illustrations may differ from what appears on the display on the actual equipment, and some of the illustrations on the display may represent something impossible in actual operation.
If the faceplate of this unit is stained, wipe it with a dry soft cloth such as a silicon cloth. If the faceplate is stained badly, wipe the stain off with a cloth moistened with neutral cleaner, then wipe neutral detergent off. Wiping the faceplate with a hard cloth or using a volatile liquid such as thinner or alcohol may scratch the surface or erases characters.
If the terminals on the unit or faceplate get dirty, wipe them with a dry, soft cloth. This unit is initially set on the Demonstration mode. However, the following control methods of the function for this unit may be differed from the Instruction manual; therefore, refer to the following supplemental instruction. Select the preset band for Auto Ensemble Memory Entry.
Press the [AME] button for at least 2 seconds. Open Auto Ensemble Memory Entry. After storing in the memory finishes, the number of the pre-set buttons and the ensemble label are displayed. If the CD center hole or outside rim has burrs, use it after removing them with a ball pen etc. The Audio file, which is out of the specification, may not able to be played normally, or the file and folder names may not be displayed correctly.
M4A", MP3: ". MP3", WMA: ". If it is attached, the file, which is not the Audio file, will be played and outputs the loud noise, and then the speaker will be damaged. The Audio file is played in the order which is written by writing soft.
You may be able to set the playing order by writing the play sequence numbers such as "01" to "99" at the beginning of the file name. CD 1 0 : Folder. When it is set to directory 4, skip to the folder before the same level by folder select. Each time the knob is pressed, the items that can be adjusted switch as shown below.
KDC-MP only. Fine-tuning so that the System Q value is optimal when setting the speaker type. The faceplate of the unit can be detached and taken with you, helping to deter theft.
For that reason, keep the faceplate in its special storage case while detached. The preset number display blinks 1 time. On each band, 1 station can be put in the memory on each [1] — [6] button. When 6 stations that can be received are put in the memory Auto Memory Entry closes. Playing discs set in the optional accessory disc player connected to this unit. If this happens, pay attention to safety and move the shift lever or take an appropriate action, then operate the unit.
Selecting the disc set in the Disc changer or the folder recorded on the Audio file media. Playing the first part of each song on the disc or Audio file folder you are listening to and searching for the song you want to listen to. The Folder Select mode releases, and the Audio file in the folder being displayed is played. A portion of the setting methods including the Tuning Mode will change.
The Menu system basic operation method is explained here. The reference for the Menu items and their setting content is after this operation explanation. Select 1 of them as the setting. Normally the uppermost setting in the chart is the original setting. Note, the Security Code can be set as the 4 digit number of your choice. A red indicator will blink on the unit after the faceplate is removed, warning potential thieves.
Switching the preout between the rear and subwoofer. In subwoofer it outputs without effect from the fader control. Temporarily have reception switched from stereo to mono to reduce multi-path noise when listening to the FM station. In such a situation, turn it OFF. It is especially important to retain the unit serial number and the electronic SIRIUS Identification number for service activation and potential future service changes. When there is a problem on playing a CD with special format, this setting play the CD by force.
Each time the knob is pressed at least 2 seconds, the Demonstration mode switches as shown below. Contact a doctor immediately if the battery is accidentally swallowed. Turning the volume down quickly. When it is pressed again, it returns to the previous level. To prevent a short circuit, remove the key from the ignition and disconnect the - battery. Make the proper input and output wire connections for each unit.
Connect the speaker wires of the wiring harness. Connect the wiring harness wires in the following order: ground, battery, ignition. Connect the wiring harness connector to the unit. Install the unit in your car. If you connect the ignition wire red and the battery wire yellow to the car chassis ground , you may cause a short circuit, that in turn may start a fire. Always connect those wires to the power source running through the fuse box. Therefore, the speaker wire should be checked.
If you connect the ignition wire to a power source with a constant voltage supply, as with battery wires, the battery may die. To prevent a short circuit, do not remove the caps on the ends of the unconnected wires or the terminals.
Changes or modifications to. The user could lose. This equipment has been tested and found to. These limits. This equipment may cause harmful. However, there is no guarantee. If this equipment does cause harmful. Refer to the catalog or consult your Kenwood. Unsupported connection may result in damage.
Setting the "O-N" Switch to the "N" position for the. The functions that can be used and the information. You must connect any of them at a time. Right after you turn on the car heater in cold. Called lens. In such. If the unit still does. To prevent injury or fire, take the. Attach the panel while you are on the. The panel lock arm will be appeared when the.
How to reset language after starting and picking wrong one. Ned, No comments 0. Pat, No comments 0. Amanda Crawford, No comments 0. What is the radio vin. Donald , No comments 0. Aaron Vasquez, No comments 0. Radio won't power on. Related product manuals. What is the difference between FM and AM?
0コメント